In this video the FL250 build is finally starting. A center-point of this 2-stroke off road go kart is this engine, so we are super eager to work on it and finally get it running. We built this motor from the ground up, including new crank bearings and seals, new crank bearings, and a new piston with a bored out cylinder. This Ody is a 1979 FL250 and we are super excited to continue and finish the restoration!
Thanks for watching and be sure to subscribe for the rest of the build!
MUSIC - If you liked the music in this video be sure to check out my buddies Soundcloud! https://soundcloud.com/shockedeel/2618a
https://andrewapplepie.bandcamp.com/track/jimmi
GPS- http://www.gopowersports.com/?utm_source=YOUTUBE&utm_campaign=Build_Break_Repeat&utm_medium=Video
STICKERS!!!
https://buildbreakrepeat.bigcartel.com
^^^^^^^^Get your stickers here ^^^^^^^
Thanks for watching and be sure to subscribe for the rest of the build!
MUSIC - If you liked the music in this video be sure to check out my buddies Soundcloud! https://soundcloud.com/shockedeel/2618a
https://andrewapplepie.bandcamp.com/track/jimmi
GPS- http://www.gopowersports.com/?utm_source=YOUTUBE&utm_campaign=Build_Break_Repeat&utm_medium=Video
STICKERS!!!
https://buildbreakrepeat.bigcartel.com
^^^^^^^^Get your stickers here ^^^^^^^
Where did you guys get your complete rebuild kit from? I am trying to find one for mine
Me gusta lo que haces tengo un buggy honda Odyssey fl250 y en mi no Ai repuestos saludo amigo
Where did you get that converter puller
Where did you get the carb kit from ?
What was the special tool you used in the threaded insert to pull the casing off?
do you know if any other style pull cords will work? a three wheeler?
Do you guys know were i can get a stator for a 79 honda oddesy
Buenos motores yo tengo uno.
good for you guys,,glad to see your not the video king guys,,cheers,
i just bought one for 250 us dlls, it´s the 2nd gen from 1983, no spark…
Before you go to the heat next time try this: Soak like you did then tighten that jack-bolt as tight a possible.
Grab a 2-3 lb metal dead-blow hammer and give the jack-bolt head a couple of good, square, robust wacks.
99% of the time that will do the trick. Heat can ruin any shaft seals on that motor and air-tight crankcase is a must.
Salut. Qu’elle et le diamètre et le pas de ton extracteur d’embrayage ? M 22 ?
Great video guys. How much did you guys spend on the full engine rebuild? Any site you recomend for restoration parts? I bought one for my son but dont know where to start. any info would be greatly appreciated. Thanks
Why are 2 strokes so cool?
never paint the head
👍👍👍👍👍👍👍👍👍👍👍👍👍
What size piston did you get? I have an 83 I just started working on it today thanks to you guys! And I took apart the engine and I’m going to have to bore the cylinder as well due to corrosion but I’m not sure what size piston I should get
If I wasn't going to replace the rod bearing ( I would of though because it most important) make sure you get all,all,all,all the sand out of the motor! You said it was open. Any sand left in the case will ruin the engine in no time at all! I had an 84 250r engine looks pretty much same same!
Does anybody know if i could take my Honda Odyssey 250 and take the engine out and put in a 1994 arctic cat zr 700 engine in it ?
I want one of those motors for my race Kart I like things with pull starts I like simple and power at its lightest possible weight
How did you guys get the top end off??
Looks brand new now
I'd like to buy this engine